The new improved CT923 Cutter allows for oil filters to be cut in either direction. This is a complete tool with no parts or adapters to change. It is very easy to use, and will provide a simple effective means of cutting open oil filters. The cutter blades in the CT923 are the same blades that are used in the CT470. Also cuts the Champion RBC308 filter used on the Rotax 912 and 914 engines.
NOTE: CT-923-4 Cutter Blade
Lead-Master wrenches reduce time to remove and install spark plug ignition leads, also permit short arc turning due to 12-point grip head.
Shipping Weight: 9.9 oz/280g
Special 3/4 in./1.9cm T handle open box wrench, 6 1/2 in./16.5cm long
Shipping weight: 4 oz/112g
Special 7/8 in./2.2cm T handle open box wrench, 6 1/2 in./16.5cm long
Shipping weight: 4 oz/112g
A companion tool to the Champion Plug-Master and other 3/8in./0.95cm square drive wrench handles. Especially designed for shielded aviation spark plugs. Built-in permanent Alnico magnet holds plugs firmly – practically eliminates dropped plugs.
Length: 3 1/2 in./8.9cm – chrome finish;
3/8 in./0.95cm – square drive
7/8 in./2.2cm – deep hex
Weight 8 1/2 oz./241g
Packed individually
Designed especially to make spark plug removal and installation easier and faster. Flex-handle allows 30-degree angle travel in either direction. Extra fine reversible ratchet action requires only 6-degree travel for next bit. Popular 3/8 in./0.95cm square drive fits Model CT-907 and other standard sockets. Knurled handle, rust-resistant chrome finish.
Approximately 11 in./27.9cm long
Weight: 12 oz./340g
Packed individually
Designed for easy removal of Cessna oil filter adapters from 150 Series thru 300 Series aircraft. Manufactured from tool quality steel, features both 3/8″ and 1/2″ drives, as well as “flip over” reversibility.
Shipping Weight: 11oz/311g
Igniter lead connector wear gauge for ARP670 type 2M fittings common to PT6 leads and others. Features a calibrated pin to measure connector wear. Opposite end sized to measure neoprene grommet expansion.
Size: 21/2 in./6.35cm.
Shipping weight: 4 oz./112g.
Carton size: 31/2 in. X 11/4 in. X 11/4 in./8.89cm. X 3.18cm. X 3.18cm.
Note: Many leads incorporate type 2M and 3M connectors at opposite ends. Both the CT-496 and CT-497 gauges are recommended.
The CT-494 accurately determines wear on 10 of our most popular surface gap igniters, insuring maximum igniter life without exceeding safe wear limitations. For use with the following igniters: CH31547, CH31621, CH34055, CH34168, CH34187, CH34269, CH34304, CH34406, FHE146-7 and FHE246-4. Heavy duty protective sleeve included.
Shipping weight: 1 oz./.28g.
A special tool designed specifically to measure the erosion-wear of Champion AA series igniters. Calibrated in colored scale segments to determine the extent of erosion of the undercut area of the steel shell, not easily visible to the eye. Measuring tips shaped to reach into the undercut, true-wear area. Instructions for use included in special plastic box.
Size: 61/4 in. X 41/4 in. X 11/2 in./15.8cm X 10.7cm X 3.8cm
Shipping weight: 10 oz./238g
For Cleaning: Two flexible rubber adapters handle 14 and 18mm plug types.
For Testing: Steel adapters of 14 and 18 mm are standard equipment and conveniently stored on the top of the cleaner for ready availability.
Molded of rugged A.B.S. plastic which is durable, oil resistant and easy to clean. An aluminum-base frame is included, which permits easy mounting to a workbench and quick removal. The solid-state ignition system produces a stable ignition test voltage providing greater accuracy and reliability. Its lack of moving parts eliminates the major cause of tester failures. Cleaning is by a dry-abrasive air blast, which quickly and effectively removes conductive deposits.
All compressed air for both cleaning and testing passes through a “built-in” automatic water trap to stop harmful airline moisture.
Height: 11 1/2 in./29.2cm
Width: 16 3/8 in./41.5cm
Depth: 12 1/8 in./30.7cm
Shipping Weight: 15 lbs./6.80kg
Color: Grey, Red, Black
Compressed Air Required: 125-180PSI/8.9-12.8kg/cm²
Electrical Requirements: 115V 60HZ 35W
Carton Size: 12 1/2 in. X 13 in. X 17 1/2 in./31.8 X 33.0 X 44.5cm
Note: Use 91893 abrasive charge only. (See following page for replacement parts list.)
Water Trap 91010
Airline Section L2 91053
Steel Adapter 18mm 91096
Airline Section L5 91138
MIrror 91836
Rubber Adapter 14mm 91657 (5-502)
Abrasive Charge 91893
Steel Adapter 12mm 92043
Airline Section L3 92048
Rubber Adapter 18mm 92203 (5-503)
Red and Black Knob Kit 92401
Adapter Hold Down Cap 92463
Switch-Push Button 92487
Valve Stem, Knob & ‘O’ Ring 92548
Cleaner Valve Assembly 92746
Water Trap Bowl Kit 92784 (L300)
Cleaner Bag/Manifold Assembly 93095
Airline Section L1 93250
Steel Nozzle Jet 93274 (5-512)
Compression Chamber Assembly 93330
Electronic Control Module/ Switch & Leads 93415
Cleaner & Bag CT-475 Only 93453 Coil 93519
Rubber Nozzle Tip 94023 (622)
Hinge and Spring Kit 94245
Air Inlet Nipple/ Mounting Nut 94283
Airline Section L4 94306
Abrasive Shield 94486
Compression Gauge 94523
Shielding Barrel Contactor 94783 (8-683)
Cleaner Bag Model 800, 2400 8-813
